ASUS IPIBL-LA MANUAL PDF

Resolve Windows 10 or update issues on an HP computer or printer — Click here. Check our tips and fixes! Sign out. Select registration option. Email address. Error: Javascript is disabled in this browser.

Author:Yolkree Kazibei
Country:Benin
Language:English (Spanish)
Genre:Literature
Published (Last):13 February 2007
Pages:426
PDF File Size:17.26 Mb
ePub File Size:4.52 Mb
ISBN:333-8-68972-539-6
Downloads:3347
Price:Free* [*Free Regsitration Required]
Uploader:Sadal



Motherboard layout Locate the CPU socket on the motherboard. Press the load lever with your thumb A , then move it to the left B until it is released from the retention tab. B A Load plate Alignment key 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom left corner of the socket then fit the socket alignment key into the CPU notch. Berkeley-GL8E 3. Close the load plate A , then push the load lever B until it snaps into the retention tab.

Under Linux, use the Hyper-Threading compiler to compile the code. If you are using any other operating systems, disable the Hyper-Threading Techonology item in the BIOS to ensure system stability and performance.

To use the Hyper-Threading Technology on this motherboard: 1. Reboot the computer. Use any of the recommended configurations on the next page. Do not create a three-dimm configuration in dual-channel mode. The third DIMM is ignored in the dual-channel operation. Berkeley-GL8E 5. Failure to do so can cause severe damage to both the motherboard and the components. To install a DIMM: 2 1. Unlock a DIMM socket by pressing the retaining clips outward.

Simultaneously press the retaining clips outward to unlock the DIMM. The DIMM might get damaged when it flips out with extra force. Remove the DIMM from the socket. Berkeley-GL8E 7. Expansion slots In the future, you may need to install expansion cards. The following sub sections describe the slots and the expansion cards that they support.

Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.

Remove the system unit cover if your motherboard is already installed in a chassis. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use. Align the card connector with the slot and press firmly until the card is completely seated on the slot. Secure the card to the chassis with the screw you removed earlier. Replace the system cover. Turn on the system and change the necessary BIOS settings, if any. Assign an IRQ to the card. Refer to the tables on the next page.

Install the software drivers for the expansion card. When using PCI cards on shared slots, ensure that the drivers support Share IRQ or that the cards do not need IRQ assignments; otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable. Refer to the table on the next page for details. The figure shows a graphics card installed on the PCI Express x16 slot. The figure shows a network card installed on the PCI Express x1 slot.

Jumpers 1. Turn OFF the computer and unplug the power cord. Removing the cap will cause system boot failure! Connectors 6. LAN RJ port. Side Speaker Out port gray. This port connects to the side speakers in an 8-channel audio configuration. Rear Speaker Out port black. This port connects to the rear speakers on a 4-channel, 6-channel, or 8-channel audio configuration. Line In port light blue. Line Out port lime.

This port connects a headphone or a speaker. In 4- channel, 6-channel, and 8-channel mode, the function of this port becomes Front Speaker Out. Microphone port pink. This port connects a microphone. Refer to the audio configuration table on the next page for the funtion of the audio ports in 2, 4, 6, or 8-channel configuration. USB 2. IEEE a port. VGA port. Berkeley-GL8E Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive.

Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. Berkeley-GL8E Floppy disk drive connector 2. The plugs from the power supply are designed to fit these connectors in only one orientation.

Find the proper orientation and push down firmly until the connectors completely fit. The minimu recommended wattage is W, or W for a fully configured system.

The system can become unstable and might experience difficulty powering up if the power supply is inadequate. You must install a PSU with a higher power rating if you intend to install additional devices. Connect the HDMI module cable to this connector, then install the module to a slot opening at the back of the system chassis. The HDMI module is purchased separately.

Connect the IEEE a module cable to this connector, then install the module to a slot opening at the back of the system chassis. Doing so will damage the motherboard! Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO not place jumper caps on the fan connectors. Connect the chassis power LED cable to this connector.

The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Reset button 2-pin RESET This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power. Motherboard layout System memory Refer to the product itself for. Chapter 1 Getting Started Thank you for choosing the v2. The v2. Designed to fit. The series mainboards are based on Intel P67 chipsets for optimal system efficiency.

Chapter 1 Getting Started Thank you for choosing the v3. Designed to fit the advanced. System Installation This chapter provides you with instructions to set up your system. Getting Started Chapter 1. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced,.

AOpen reserves the right to revise all the specifications and information contained in this document which is subject to change without notice.

No part of this manual, including the products and software described in it, may be. MA User Manual Version 3. All rights reserved.

GUSTAW HERLING GRUDZINSKI WIEZA PDF

Asus IPIBL-LA Berkeley-GL8E Manuals

Motherboard layout Locate the CPU socket on the motherboard. Press the load lever with your thumb A , then move it to the left B until it is released from the retention tab. B A Load plate Alignment key 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom left corner of the socket then fit the socket alignment key into the CPU notch. Berkeley-GL8E 3. Close the load plate A , then push the load lever B until it snaps into the retention tab.

LIQUID ATOMIZATION BAYVEL PDF

Asus IPIBL-LA Berkeley-GL8E Instruction Manual

Menu Menu. Search Everywhere Threads This forum This thread. Search titles only. Search Advanced search…. Everywhere Threads This forum This thread.

Related Articles