|Published (Last):||13 June 2017|
|PDF File Size:||13.74 Mb|
|ePub File Size:||1.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thank you for interesting in our services. We are a non-profit group that run this website to share documents. We need your help to maintenance this website. Please help us to share our service with your friends. Share Embed Donate. No part of this publication may be reproduced, modified, or distributed without prior written authorization of Ceragon Networks Ltd.
This document is provided as is, without warranty of any kind. Other names mentioned in this publication are owned by their respective holders. Statement of Conditions The information contained in this document is subject to change without notice. Ceragon Networks Ltd. All rights reserved. Corporate Headquarters: Ceragon Networks Ltd. A-1 General A-1 GHz Frequency Channels Before turning on the equipment, make sure that the fiber optic cable is intact and is connected to the transmitter.
Do not attempt to adjust the laser drive current. The use of optical devices with the equipment will increase eye hazard. Use of controls, adjustments, or performing procedures other than those specified herein, may result in hazardous radiation exposure. When working with a FibeAir IDU, note the following risk of electric shock and energy hazard: Diconnecting one power supply disconnects only one power supply module.
To isolate the unit completely, disconnect all power supplies. Machine noise information order - 3. To prevent damage, before touching components inside the device, all electrostatic must be discharged from both personnel and tools. Versuchen Sie nicht, den Laser-Antriebsstrom zu regulieren. Traffic capacity throughput and spectral efficiency are optimized with the desired channel bandwidth.
High spectral efficiency is ensured using the same bandwidth for double the capacity, via two carriers, with vertical and horizontal polarizations. This feature is implemented by a built-in XPIC mechanism. RFU-C works together with two types of indoor units. This enables double capacity in the same spectrum bandwidth.
If needed, change the antenna polarization by rotating the RFU-C in accordance with the relevant antenna installation guide. Vertical Pole Horizontal Pole 2.
Spread grease on the O-ring supplied with the antenna. Place the O-ring in its location on the antenna transition. Remove the sticker from the RFU-C antenna interface. Mount the RFU-C on the antenna according to the system configuration, and make sure that the twist is set for the desired polarization horizontal or vertical.
Insert four screws and washers provided with the kit, and tighten them. If needed, change the antenna polarization according to the relevant antenna installation guide. Spread grease on the two O-rings supplied with the kit and place them in their locations.
Mount the twist on the coupler according to the relevant antenna polarization as shown in the illustrations below , using four screws and washers supplied with the kit. Place the O-ring on the antenna transition. Mount the coupler holder on the antenna using the screws and washers supplied with the kit.
Spread grease on the O-rings supplied with the holder coupler kit. Place one O-ring on each side of the coupler. Remove the sticker from both RFU-C antenna interfaces. Mount both RFU-Cs on the holder coupler. For each RFU-C, insert four screws and washers, and tighten them, as shown in the following illustration. Mount the Ceragon remote mount device on the pole, as shown in the following illustration. Insert four screws and washers, and tighten them.
Spread grease on the O-ring supplied with the flexible waveguide. Place the O-ring in the flexible waveguide flange groove. Place the O-ring in the other end of the flexible waveguide flange groove. Mount the flexible waveguide on the antenna, and tighten the screws and washers.
Mount the Ceragon remote mount device on the pole. Mount the coupler holder on the Ceragon remote mount device using the screws and washers supplied with the kit. Spread grease on the O-rings supplied with the coupler holder kit.
Mount both RFU-Cs on the coupler holder. For each RFU-C, insert four screws and washers, and tighten them. Mount the flexible waveguide on the Ceragon coupler, and tighten the screws and washers. The antenna interface is always the RFU-C interface. If other antennas are to be used, an adaptor with a 0. An adapter is used for the direct mount, as shown in the following illustration.
The same antenna type integrated as indicated above can be used recommended. Other antenna types using the flanges listed in the table below may be used. Please contact your Ceragon representative for details. Transportation The equipment should be prepared for public transportation. The cargo must be kept dry during transportation, in accordance with ETS , Class 2. It is recommended that the equipment be transported to the installation site in its original packing case. If intermediate storing is required, the packed equipment must be stored in a dry and cool environment, and out of direct sunlight, in accordance with ETS , Class 1.
Inspection Check the packing lists and verify that the correct equipment part numbers and quantities are found in the packages that arrived. Acceptance and commissioning should be performed after initial setup is complete. The purpose of this procedure is to verify correct installation and operation of the installed link and the interoperability with customer end equipment.
Note: RFU-C works together with two types of indoor units. Following this procedure will ensure proper, long-lasting, and safe operation of the product. The checklist below summarizes the installation requirements of the site. Antenna Mounting Mounting pole is of sufficient height to clear local obstructions, such as parapets, window cleaning gantries, and lift housings.
Mounting Pole is of sufficient height, and is safely positioned, so as not to cause a safety hazard. No person should be able to walk in front of, or look directly into the path of the microwave radio beam. Where possible, the pole should be away from the edge of the building.
Mounting pole is secure and perpendicular. A pole that is not perpendicular may cause problems during antenna alignment. Mounting pole is grounded as per site specifications. All operators and site owners have specific requirements regarding the grounding of installations. As a minimum, typical requirements are such that any metal structure must be connected to the existing lightning protection ground of the building.
Where it extends beyond the 45 degree cone of protection of existing lightning conductors, additional lightning protectors should be installed. All steelwork is Galvanized or Stainless Steel, as appropriate to prevent corrosion. Antenna Antenna is grounded as per site specifications. See the third point in the Antenna Mounting section above. Antenna sway braces are fitted and installed correctly, where applicable. Typically, for an antenna of 1. This sway brace should not be mounted to the same pole as the antenna, but should be installed directly back to the tower or an alternative point.
Antenna Water Drain Plugs are fitted and removed, where appropriate. Some antennas have moisture drain plugs installed at various points around the antenna. The purpose of these plugs is to allow any moisture that forms on the inside of the antenna or radome to drip out and prevent a pool within the antenna. Only the plugs at the bottom of the antenna, after installation, should be removed. All other plugs should be left in position. The RFU polarization is as per link requirements and matches the polarization of the antenna.
Indoor Unit The main traffic connections are correctly terminated and crimped as per cable and connector manufacturer instructions. All fiber optic patch leads should be routed carefully and efficiently, using conduits to prevent damage to the cables. All other user terminations are secure and correctly terminated.
All labeling is complete as per site requirements.
Ceragon Fibe-Air IP-10G Manuals
Embed Size px x x x x NoticeThis document contains information that is proprietary to Ceragon Networks Ltd. No part of this publication may be reproduced, modified, or distributed without prior written authorization of Ceragon Networks Ltd. This document is provided as is, without warranty of any kind. Other names mentioned in this publication are owned by their respective holders. Statement of ConditionsThe information contained in this document is subject to change without notice. Ceragon Networks Ltd.
Ceragon FibeAir-IP10 Manual
Thank you for interesting in our services. We are a non-profit group that run this website to share documents. We need your help to maintenance this website. Please help us to share our service with your friends. Share Embed Donate.
ceragon fibeair-ip10 manual